![]() |
Earlier / Obsolete Products Nearest Equivalent Product Comments MTL4013 MTL4513 MTL4014 MTL4504 Phase reversal added. MTL4015 MTL4511 No repeat contact on MTL4511. use MTL4510B if required. Check connections on terminals 7 & 9. MTL4016 MTL4516 No repeat contact on MTL4516. use MTL4510B if required. ... Read More
|
![]() |
Earlier / Obsolete Products Nearest Equivalent Product Comments MTL5011B MTL5511 MTL5012 Use 1ch of MTL5513 MTL5012S No replacement MTL5014 MTL5514/14D MTL5514 does not provide 1in 2out function, MTL5514D with 1in 2out LFD relay energises alarm. MTL5015 MTL5513 Common connection on haz side, max ... Read More
|
![]() |
西门子Sinamics S120 是西门子公司推出的全新的集V/F、矢量控制及伺服控制于一体的驱动控制系统,它不仅能控制普通的三相异步电动机,还能控制同步电机、扭矩电机及直线电机。其强大的定位功能将实现进给轴的绝对、相对定位。 共直流母线的DC/AC 逆变器通常又称为西门子Sinamics S120 多轴驱动器,其结构形式为电源模块和电机模块分开,一个电源模块将3 相交流电整流成540V 或600V 的直流电,将电机模块(一个或多个)都连接到该直流母线上,特别适用于多轴控制,尤其是造纸、包装、纺织、印刷、钢铁等行业。优点是各电机轴之间的能量共享,接线方便、简单。 1、控制单元:CU320... Read More
|
![]() |
MTL4500 - MTL5500 SERIES COMMON SPECIFICATIONS Connectors Each unit is supplied with signal connectors, as applicable. When using crimp ferrules for the hazardous or non-hazardous (safe) signal connectors the metal tube length should be 12mm and the wire trim length 14mm. Isolation 250V rms, tested ... Read More
|
![]() |
MTL5532 PULSE ISOLATOR MTL5532 isolates pulses from a switch, proximity detector, current pulse transmitter or voltage pulse transmitter located in a hazardous area. It is ideal for applications involving high pulse rates and fast response times, by repeating the pulses into the safe area. An ... Read More
|
![]() |
MTL5516/C Switch/ Proximity Detector Interface 2-Channel, With Line Fault Detection MTL5516/C enable two safe-area loads to be controlled by a switch or proximity detector located in a hazardous-area. When selected, open or short circuit conditions in the field wiring are detected by the line-fault... Read More
|
![]() |
MTL5549/Y isolating driver two-channel, for 4–20mA, HART® valve positioners with line fault detection MTL5549 accepts 4/20mA floating signals from safe-area controllers to drive 2 current/pressure converters (or any other load up to 800Ω) in a hazardous area. For HART valve positioners, the module ... Read More
|
![]() |
MTL5531 VIBRATION TRANSDUCER INTERFACE MTL5531 repeats a signal from a vibration sensor in a hazardous area, providing an output for a monitoring system in the safe area. The interface is compatible with 3-wire eddy-current probes and accelerometers or 2-wire current sensors; the selection is made ... Read More
|
![]() |
MTL5546/Y isolating driver for 4–20mA HART® valve positioners with line fault detection MTL5546 accepts a 4/20mA floating signal from a safe-area controller to drive a current/pressure converter (or any other load up to 800Ω) in a hazardous area. For HART valve positioners, the module also permits ... Read More
|
![]() |
MTL5544D repeater power supply single channel, 4/20mA, HART® for 2- or 3-wire transmitters, two outputs MTL5544D provides a fully-floating dc supply for energising a conventional 2- or 3-wire 4/20mA transmitter located in a hazardous area, and repeats the current in other circuits to drive two safe... Read More
|